近期论文
查看导师新发文章
（温馨提示：请注意重名现象，建议点开原文通过作者单位确认）
T.L. Huang*, L.F. Shuai, A. Wakeel, G.L. Wu*, N. Hansen, X. Huang. Strengthening Mechanisms and Hall-Petch Stress of Nanotructured Al-0.3%Cu. Acta Materialia, 156 (2018), 369-378. Q.Y. He, T.L. Huang*, L.F. Shuai, Y.B. Zhang, G.L. Wu*, X. Huang, D. Juul Jensen. In-situ Investigation of the Evolution of Annealing Twins in High Purity Aluminium. Scripta Materialia, 153(2018), 68-72. (Open access) L.F. Shuai, T.L. Huang*, G.L. Wu*, X. Huang, O.V. Mishin. Development of Gosstexture in Al-0.3%Cu annealed after heavy rolling. Journal of Alloys and Compounds, (2018), DOI: 10.1016/j.jallcom.2018.03.187. Z.X. Cao, G.L. Wu, X.J. Sun, C. Wang, D. Pong, W.Q. Cao*. Revealing the superplastic deformation behaviors of hot rolled 0.10C5Mn2Al steel with an initial martensitic microstructure. Scripta Materials, 152(2018), 27-30. R.G. Lia, Q.G. Xie, Y.D. Wang*, W.J. Liu, M.G. Wang, G.L. Wu, X.W. Li, M.H. Zhang, Z.P. Lu, C.G. Geng, T. Zhu. Unraveling submicron-scale mechanical heterogeneity by three-dimensional X-ray microdiffraction. Proceeding of the National Academy of Science, USA (PNAS), 115 (2018), 483-488. L. Xie, T.L. Huang, Y.H. Wang, G.L. Wu*, N. Tsuji, X.X. Huang*. Deformation Induced Martensitic Transformation and Its Initial Microstructure Dependence in a High Alloyed Duplex Stainless Steel. Steel Research Inter., 87(2017), 1700169.L. Zhang, Z. Chen, Y.H. Wang, G.Q. Ma, T.L. Huang, G.L. Wu*, D. Juul Jensen. Fabricating interstitial-free steel with simultaneous high strength and good ductility with homogeneous layer and lamella structure. Scripta Mater., 141(2017), 111-114. Z.Q. Feng, C.W. Lin, T.T. Li, X. Luo, G.L. Wu, X.X. Huang. Electron tomography of dislocations in an Al-Cu-Mg alloy. IOP Conf. Series: Materials Science and Engineering, 219(2017) 012018. Q.Y. He, M. Zhu, Q.S. Mei, C.S. Hong, G.L. Wu, X. Huang. Microstructural and hardness gradients in Cu processed by high pressure surface rolling.IOP Conf. Series: Materials Science and Engineering, 219(2017) 012025. L.F. Shuai, T.L. Huang, G.L. Wu, N. Hansen and X. Huang. Characterization of Cu Distribution in an Al-0.3%Cu Alloy Cold Rolled to 98%. IOP Conf. Series: Materials Science and Engineering, 219(2017) 012038. L. Xie, T.L. Huang, Y.H. Wang, L. Zhang, G.L. Wu, N. Tsuji and X. Huang. Structural refinement and property optimization in an Fe-23Cr-8.5Ni duplex stainless steel. IOP Conf. Series: Materials Science and Engineering, 219 (2017) 012045. R. Yang, X. Zhang, D. Mallipeddi, N. Angelou, H.L. Toftegaard, Y. Li, J. Ahlström, L. Lorentzen, G. Wu, X. Huang. Effect of shot peening on the residual stress and mechanical behaviour of low-temperature and high-temperature annealed martensitic gear steel 18CrNiMo7-6. IOP Conf. Series: Materials Science and Engineering, 219 (2017) 012046. R. Yang, G.L. Wu, X. Zhang, W.T. Fu and X. Huang. Gradient microstructure and microhardness in a nitrided 18CrNiMo7-6 gear steel. IOP Conf. Series: Materials Science and Engineering, 219 (2017) 012047. C.L. Zhang, Y.B. Zhang, G.L. Wu, W. Liu, D. Juul Jensen and A. Godfrey. Quantification of deformation microstructure at ultra-low tensile strain in pure Al prepared by spark plasma sintering. IOP Conf. Series: Materials Science and Engineering, 219 (2017) 012050. J. Zhang, G.Q. Ma, A. Godfrey, D.Y. Shu, Q. Chen, G.L. Wu. Orientation Dependence of the Deformation Microstructure of Ta-4%W after Cold-Rolling. IOP Conf. Series: Materials Science and Engineering, 219 (2017) 012051. L. Zhang, X.J. Jiang, Y.H. Wang, Q. Chen, Z. Chen, Y.H. Zhang, T.L. Huang, G.L. Wu. Heterogeneous multi-layered IF steel with simultaneous high strength and good ductility. IOP Conf. Series: Materials Science and Engineering, 219 (2017) 012052. Q. Chen, D. Y. Shu, J. Lin, Y. Wu, X. S. Xia, S. H. Huang, Z. D. Zhao, O. V. Mishin, G. L.Wu*. Evolution of Microstructure and Texture in Copper during Repetitive Extrusion-Upsetting and Subsequent Annealing. Journal of Materials Science and Technology. 33(2017), 690-697. C.L. Xu, Y.B. Zhang, A.W. Godfrey, G.L. Wu, W.J. Liu, J.Z. Tischler, Q. Liu, D. Juul Jensen. Direct observation of nucleation in the bulk of an opaque sample. Scientific Reports, 2017, DOI: 10.1038/srep42508. Q. Chen, D. Y. Shu, J. Lin, Y. Wu, X. S. Xia, S. H. Huang, Z. D. Zhao, O. V. Mishin, G. L. Wu. Evolution of Microstructure and Texture in Copper during Repetitive Extrusion-Upsetting and Subsequent Annealing. Journal of Materials Science and Technology. 2017, DOI: 10.1016/j.jmst.2017.03.003. Dong Yue Xie , Jiawei Yan, Yangxin Li, Dong Qiu, Guilin Wu, Xiaodong Wang, Bin Chen, Yao Shen, Guo-zhen Zhu. Ordered stacking faults within nanosized silicon precipitates in aluminum alloy. Materials Letters, 190 (2017), 225-228. DOI:10.1016/j.matlet.2017.01.023 Changfa Guo, Xuan Luo, Yunchang Xin, Guilin Wu, Qing Liu. Obtaining high strength and high plasticity in a Mg-3Al-1Zn plate using pre-tension and annealing treatments. Journal of Alloy and Compound, 704 (2017), 406-412. C.L. Xu, Y.B. Zhang, F.X. Lin, G.L. Wu, Q. Liu, D. Juul Jensen. Statistical Analysis of Nucleation at Hardness Indentations in High Purity Aluminum. Metallurgy & Materials Transaction A, 47 (2016) 5863-5870. DOI:10.1007/s11661-016-3704-3.
京公网安备 11010802027423号