Khan, Zulfiqar - Bournemouth University - Department of Design & Engineering

个人简介

Dr Zulfiqar Khan (Associate Professor) is currently leading NanoCorr, Energy and Modelling (NCEM) Research Theme within the University Design & Engineering Research Centre.

近期论文

查看导师新发文章（温馨提示：请注意重名现象，建议点开原文通过作者单位确认）

Saeed, A., Khan, Z., Nazir, H., Hadfield, M. and Smith, R., 2017. Research impact of conserving large military vehicles through a sustainable methodology. International Journal of Heritage Architecture, 1 (2), 267-274. Nazir, M.H., Khan, Z.A. and Stokes, K., 2016. Analysing the coupled effects of compressive and diffusion induced stresses on the nucleation and propagation of circular coating blisters in the presence of micro-cracks. Engineering Failure Analysis, 70, 1-15. Khan, Z., Khan, Z. and Tabeshf, K., 2016. Parametric investigations to enhance thermal performance of paraffin through a novel geometrical configuration of shell and tube latent thermal storage system. Energy Conversion and Management, 127, 355-365. Roberts, A., Thomas, B., Sewell, P., Khan, Z., Balmain, S. and Gillman, J., 2016. Current tidal power technologies and their suitability for applications in coastal and marine areas. Journal of Ocean Engineering and Marine Energy. Khan, Z., Saeed, A., Gregory, E. and Ghafoor, A., 2016. Biodiesel Performance within Internal Combustion Engine Fuel System - A Review. Tribology in Industry, 38 (2), 197-213. Khan, Z., Khan, Z. and Ghafoor, A., 2016. A review of performance enhancement of PCM based latent heat storage system within the context of materials, thermal stability and compatibility. Energy Conversion and Management, 115, 132-158. Nazir, M.H., Khan, Z.A., Saeed, A. and Stokes, K., 2016. A predictive model for life assessment of automotive exhaust mufflers subject to internal corrosion failure due to exhaust gas condensation. Engineering Failure Analysis, 63, 43-60. Nazir, M.H., Khan, Z.A., Saeed, A. and Stokes, K., 2016. A model for cathodic blister growth in coating degradation using mesomechanics approach. Materials and Corrosion, 67 (5), 495-503. Helvaci, H.U. and Khan, Z., 2016. Experimental Study of Thermodynamic Assessment of a Small Scale Solar Thermal System. Energy Conversion and Management. Nazir, M.H., Khan, Z.A., Saeed, A. and Stokes, K., 2016. Modeling the effect of residual and diffusion-induced stresses on corrosion at the interface of coating and substrate. Corrosion, 72 (4), 500-517. Gultekin, A., Pashaei, P., Khan, Z., Ozturk, M.K., Tamer, M. and Bas, Y., 2016. Dft And X-ray Study Of Structural, Electronic, Elastic And Optical Properties In Be1–xznxs Alloys Depending On Vegard’s Law. International Journal of Computational Methods and Experimental Measurements, 3 (4), 340-349. Bajwa, R., Khan, Z., Nazir, H., Chacko, V. and Saeed, A., 2016. Wear and friction properties of electrodeposited Ni-based coatings subject to nano-enhanced lubricant and composite coating. Acta Metallurgica Sinica (English Letters), 29 (10), 902-910. Bajwa, R.S., Khan, Z., Bakolas, V. and Braun, W., 2016. Water-lubricated Ni-based composite (Ni-Al2O3, Ni-SiC and Ni-ZrO2) thin film coatings for industrial applications. Acta Metallurgica Sinica (English Letters), 29 (1), 8-16. Nazir, H. and Khan, Z., 2016. Maximising the interfacial toughness of thin coatings and substrate through optimisation of defined parapmeters. International Journal of Computational Methods & Experimental Measurements, 3 (4), 316-328. Helvaci, H.U. and Khan, Z.A., 2015. Mathematical modelling and simulation of multiphase flow in a flat plate solar energy collector. Energy Conversion and Management, 106, 139-150. Bajwa, R.S., Khan, Z., Bakolas, V. and Braun, W., 2015. Effect of bath ionic strength on adhesion and tribological properties of pure nickel and Ni-based nanocomposite coatings. Journal of Adhesion Science and Technology, 1-13. Saeed, A., Khan, Z.A. and Nazir, M.H., 2015. Time dependent surface corrosion analysis and modelling of automotive steel under a simplistic model of variations in environmental parameters. Materials Chemistry and Physics. Wen, B., Khan, Z. and Helvaci, U., 2015. Simulation study of a large scale flat plate solar collector with continuous serpentine tubing configuration for domestic hot water pre-heating and space heating applications. Energy Conversion and Management. Nazir, M., Khan, Z. and Stokes, K., 2015. Optimisation of Interface Roughness and Coating Thickness to Maximise Coating-Substrate Adhesion - A Failure Prediction and Reliability Assessment Modelling. Journal of Adhesion Science and Technology, 29 (14), 1415-1445. Nazir, H., Khan, Z. and Stokes, K., 2015. A Unified Mathematical Modelling and Simulation for Cathodic Blistering Mechanism incorporating diffusion and fracture mechanics concepts. Journal of Adhesion Science and Technology, 29 (12), 1200-1228.