研究领域
Fuel Cells (Fuel Processing, Fuel Cell Materials and Fuel Cell Modelling)
Solid Oxide Electrolysis (Renewable Hydrogen and Synthetic Fuel Production)
Application of Kinetics, Catalysis and Chemical Reaction Engineering.
Process Modelling and Simulation
近期论文
查看导师新发文章
(温馨提示:请注意重名现象,建议点开原文通过作者单位确认)
A. Amiri, P. Vijay, M. O. Tadé, K. Ahmed, G. D. Ingram, V. Pareek, R. Utikar, “Solid oxide fuel cell reactor analysis and optimization through a novel multi-scale modelling strategy”, Computers & Chemical Engineering, 78 (2015) 10.
P. Vijay, M. O. Tade, K. Ahmed, R. Utikar, and V. K. Pareek. 2014. “Simultaneous estimation of states and inputs in a planar solid oxide fuel cell using nonlinear adaptive observer design.” Journal of Power Sources 248 (2014) 1218.
S. Hosseini, K. Ahmed and M.O. Tade, “CFD model of a methane fueled single cell SOFC stack for analyzing the combined effects of macro/micro structural parameters”, Journal of Power Sources 234 (2013) 180.
K. Ahmed and K. Föger, “Fuel Processing for High-Temperature High-Efficiency Fuel Cells”, Industrial & Engineering Chemistry Research, 49 (2010) 7239.
K. Föger and K. Ahmed, “Catalysis in High-Temperature Fuel Cells”, Journal of Physical Chemistry B, 109 (2005) 2149.
K. Ahmed, J. Gamman and K. Föger, “Demonstration of LPG-fueled solid oxide fuel cell systems”, Solid State Ionics, 152-153, (2002) 485.
K. Ahmed and K. Föger, “Approach to equilibrium of the water-gas shift reaction under fuel-cell conditions”, Journal of Power Sources, 103 (2001) 150.
K. Ahmed and K. Föger, “Kinetics of internal steam reforming of methane on Ni-YSZ based anodes for solid oxide fuel cells”, Catalysis Today, 63 (2000) 479.
K. Ahmed, Y. Ramprakash, R. Bolden and K. Föger, “Performance of a methane-fueled single cell SOFC stack at various levels of fuel utilization”, Journal of Australasian Ceramic Society, Vol. 34, No.1, (1998) 225
K. Ahmed, K.A. Islam and S. Ali, "An optimal operating policy for high temperature shift converters", Chemical Engineering Research & Design, 72A (1994) 645.
K. Ahmed and H.M. Chowdhury, "Dehydrogenation of cyclohexane and cyclohexene over supported nickel and platinum catalysts", The Chemical Engineering Journal, 50 (1992) 165.
K. Ahmed and P. Mistry, "Effect of calcination temperature on nickel/alumina catalysts", Collections of Czechoslovak Chemical Communications, 57 (1992) 2073.
K. Ahmed, L.S. Kershenbaum, and D. Chadwick, "Adsorption of thiophene on nickel/alumina catalysts", Industrial & Engineering Chemistry Research, 29 (1990) 150.
K. Ahmed and S.C. Das, "Modelling of sulphur poisoning of CO methanation”, Indian Chemical Engineer, 32 (1990) T67.
K. Ahmed, L.S. Kershenbaum, D. Chadwick, "Sintering effects in a nickel/alumina catalyst", Chemical Engineering Science, 44(1989) 999.
S. Hosseini, M.O. Tadé and K. Ahmed, “On the effects of geometry and methane reforming kinetics in predicted results from the mechanistic model of a planar SOFC”. CHEMECA 2011: Engineering a Better World: Sydney Hilton Hotel, NSW, Australia, 18-21 September 2011, 1514.
K. Ahmed and K. Föger, “Thermodynamic analysis of diesel reforming options for SOFC systems”, Proc. 8th International Symposium on Solid Oxide Fuel Cells, The Electrochemical Society, NJ, 2003, p. 1240.
R. Ratnaraj, K. Ahmed, J. Love, S. Amarasinghe, O. Bellon and K. Föger, “Material design and processing of CFCL’s cell assembly”, Proc. 8th International Symposium on Solid Oxide Fuel Cells, The Electrochemical Society, NJ, 2003, p. 944.
K. Ahmed, J. Love and R. Ratnaraj, “High performance cell development at CFCL”, Proc. 7th International Symposium on Solid Oxide Fuel Cells, The Electrochemical Society, NJ, 2001, p.904.
K. Ahmed, J. Gamman and K. Föger, “Catalyst Screening for pre-reforming of LPG for solid oxide fuel cell systems”, accepted for 6th World Congress of Chemical Engineering, Melbourne, 2001.