近期论文

查看导师新发文章 （温馨提示：请注意重名现象，建议点开原文通过作者单位确认）

Johnston, Sean, Shi, Zhiming, Dargusch, Matthew S. and Atrens, Andrej (2016) Influence of surface condition on the corrosion of ultra-high-purity Mg alloy wire. Corrosion Science, 108 66-75. doi:10.1016/j.corsci.2016.03.007 Li, Tong, Kent, Damon, Sha, Gang, Cairney, Julie M. and Dargusch, Matthew S. (2016) The role of ω in the precipitation of α in near-β Ti alloys. Scripta Materialia, 117 92-95. doi:10.1016/j.scriptamat.2016.02.026 Li, Tong, Kent, Damon, Sha, Gang, Stephenson, Leigh T., Ceguerra, Anna V., Ringer, Simon P., Dargusch, Matthew S. and Cairney, Julie M. (2016) New insights into the phase transformations to isothermal ω and ω-assisted α in near β-Ti alloys. Acta Materialia, 106 353-366. doi:10.1016/j.actamat.2015.12.046 Zhan, Hongyi, Wang, Gui, Kent, Damon and Dargusch, Matthew (2016) The dynamic response of a metastable β Ti-Nb alloy to high strain rates at room and elevated temperatures. Acta Materialia, 105 104-113. doi:10.1016/j.actamat.2015.11.056 Yu, Hua, Ye, Delai, Butburee, Teera, Wang, Lianzhou and Dargusch, Matthew (2016) Green synthesis of porous three-dimensional nitrogen-doped graphene foam for electrochemical applications. ACS Applied Materials and Interfaces, 8 4: 2505-2510. doi:10.1021/acsami.5b09030 Yu, Hua, Wang, Lianzhou and Dargusch, Matthew (2016) Low-temperature templated synthesis of porous TiO2 single-crystals for solar cell applications. Solar Energy, 123 17-22. doi:10.1016/j.solener.2015.10.044 Shi, Zhiming, Kim, W. J., Cao, Fuyong, Dargusch, Matthew S. and Atrens, Andrej (2015) Stress corrosion cracking of high-strength AZ31 processed by high-ratio differential speed rolling. Journal of Magnesium and Alloys, 3 4: 271-282. doi:10.1016/j.jma.2015.11.006 Zhang, Yaowu, Kent, Damon, Wang, Gui, St John, David and Dargusch, Matthew (2015) An investigation of the mechanical behaviour of fine tubes fabricated from a Ti-25Nb-3Mo-3Zr-2Sn alloy. Materials and Design, 85 256-265. doi:10.1016/j.matdes.2015.06.127 Chen, Jing, Xiao, Wenlong, Dargusch, Matthew Simon and Ma, Chaoli (2015) The Dependence of Isothermal ω Precipitation on the Quenching Rate in a Metastable β-Ti Alloy. Scientific Reports, 5 Art No.: 14632: . doi:10.1038/srep14632 Zhan, Hongyi, Zeng, Weidong, Wang, Gui, Kent, Damon and Dargusch, Matthew (2015) On the deformation mechanisms and strain rate sensitivity of a metastable β Ti-Nb alloy. Scripta Materialia, 107 34-37. doi:10.1016/j.scriptamat.2015.05.014 Rahman Rashid, R. A., Palanisamy, S., Sun, S. and Dargusch, M. S. (2015) Tool wear mechanisms involved in crater formation on uncoated carbide tool when machining Ti6Al4V alloy. International Journal of Advanced Manufacturing Technology, 1-9. doi:10.1007/s00170-015-7668-z Gao, Yanfeng, Wang, Gui, Bermingham, Michael J. and Dargusch, Matthew S. (2015) Cutting force, chip formation, and tool wear during the laser-assisted machining a near-alpha titanium alloy BTi-6431S. International Journal of Advanced Manufacturing Technology, 79 9-12: 1949-1960. doi:10.1007/s00170-015-6917-5 Zhu, Suming, Easton, Mark A., Abbott, Trevor B., Nie, Jian-Feng, Dargusch, Matthew S., Hort, Norbert and Gibson, Mark A. (2015) Evaluation of magnesium die-casting alloys for elevated temperature applications: microstructure, tensile properties, and creep resistance. Metallurgical and Materials Transactions A, 46 8: 3543-3554. doi:10.1007/s11661-015-2946-9 Sun, Shoujin, Brandt, Milan, Palanisamy, Suresh and Dargusch, Matthew S (2015) Effect of cryogenic compressed air on the evolution of cutting force and tool wear during machining of Ti-6Al-4V alloy. Journal of Materials Processing Technology, 221 243-254. doi:10.1016/j.jmatprotec.2015.02.017 Zhu, Y. M., Zhu, S. M., Dargusch, M. S. and Nie, J. F. (2015) HAADF-STEM study of phase separation and the subsequent α phase precipitation in a β-Ti alloy. Scripta Materialia, 112 46-49. doi:10.1016/j.scriptamat.2015.09.007 Bermingham, M. J., Kent, D., Zhan, H., StJohn, D. H. and Dargusch, M. S. (2015) Controlling the microstructure and properties of wire arc additive manufactured Ti–6Al–4V with trace boron additions. Acta Materialia, 91 289-303. doi:10.1016/j.actamat.2015.03.035 Cao, Fuyong, Shi, Zhiming, Song, Guang-Ling, Liu, Ming, Dargusch, Matthew S. and Atrens, Andrej (2015) Influence of casting porosity on the corrosion behaviour of Mg0.1Si. Corrosion Science, 94 255-269. doi:10.1016/j.corsci.2015.02.002 Bermingham, M. J., Kent, D. and Dargusch, M. S. (2015) A new understanding of the wear processes during laser assisted milling 17-4 precipitation hardened stainless steel. Wear, 328-329 518-530. doi:10.1016/j.wear.2015.03.025 Shi, Zhiming, Hofstetter, Joelle, Cao, Fuyong, Uggowitzer, Peter J., Dargusch, Matthew S. and Atrens, Andrej (2015) Corrosion and stress corrosion cracking of ultra-high-purity Mg5Zn. Corrosion Science, 93 330-335. doi:10.1016/j.corsci.2015.01.032 Zhan, Hongyi, Zeng, Weidong, Wang, Gui, Kent, Damon and Dargusch, Matthew (2015) Microstructural characteristics of adiabatic shear localization in a metastable beta titanium alloy deformed at high strain rate and elevated temperatures. Materials Characterization, 102 103-113. doi:10.1016/j.matchar.2015.02.017