近期论文
查看导师新发文章
（温馨提示：请注意重名现象，建议点开原文通过作者单位确认）
[1]王继超,杨振强.基于细菌觅食优化算法的永磁同步电机位置伺服系统模糊控制策略[J],电机与控制应用,2017,44(6):40-44,96
[2]甄自源,杨振强.飞锯控制系统锯车位置和速度的测量方法[J],组合机床与自动化加工技术,2016,11:100-104
[3]张信,杨振强,吴梦杰.基于电流估计的永磁同步电机矢量控制[J],微特电机,2016,44(5):52-55,59
[4]谭俊杰,杨振强,杜署明.自平衡两轮车的线性霍耳位置检测技术研究[J],电气传动,2015,45(8):67-71,80
[5]李明中,杨振强,张峰.基于电压模型改进型定子磁链观测器[J],微电机,2015,6:65-68
[6]高泽飞,董伟,谭毅,杨振强.PLC在真空熔炼炉系统中的应用[J],工业控制计算机,2012,25(8):126-127
[7]Yu, Shuanghe,Yang, Zhenqiang,Du, Jialu,Ma, Jingcong.Sliding Mode Observer Based Anti-Windup PI Speed Controller for Permanent Magnet Synchronous Motors[A],7th International Conference on Intelligent Computing (ICIC),2012,6839:325-+
[8]谭毅,杨振强.Effect of Temperature on Performance Parameters of Metallurgical Grade Polysilicon Solar Cells[J],Applied Mechanics and Materials,2012,148(1):1252-1255
[9]Long X.-J.,Yu S.-H.,Yang Z.-Q.,Du J.-L..Speed regulation of permanent magnet synchronous motor based on active disturbance rejection control[J],Zhongnan Daxue Xuebao (Ziran Kexue Ban)/Journal of Central South University (Science and Technology),2011,42(SUPPL. 1):376-379
[10]Ge J.-Q.,Yu S.-H.,Yang Z.-Q.,Du J.-L..Permanent magnet synchronous motor control and performance analysis based on interconnection and damping assignment[J],Zhongnan Daxue Xuebao (Ziran Kexue Ban)/Journal of Central South University (Science and Technology),2011,42(SUPPL. 1):1003-1008
[11]Yu S.-H.,Du J.-L.,Zhou L.-N.,Yang Z.-Q..Design and analysis of speed regulation of permanent magnet synchronous motor based on fuzzy logic[J],Zhongnan Daxue Xuebao (Ziran Kexue Ban)/Journal of Central South University (Science and Technology),2011,42(SUPPL. 1):1032-1036
[12]葛建强,于双和,杨振强,杜佳璐.基于互联阻尼分配方法的永磁同步电机控制与性能分析[A],2011,VOL.42:1003-1008
[13]于双和,杜佳璐,周丽娜,杨振强.基于模糊逻辑的永磁同步电机调速方法设计与分析[A],2011,VOL.42:1032-1036
[14]龙晓军,于双和,杨振强,杜佳璐.基于自抗扰技术的永磁同步电机调速方法[A],2011年中国智能自动化会议,2011,VOL.42:376-379
[15]Yan, Yan,Yu, Shuanghe,Yang, Zhenqiang,Du, Jialu.A Continuous Output Feedback Finite-Time Speed Tracking Control of PMSM[A],2nd International Conference on Advanced Measurement and Test (AMT 2011),2011,301-303:1384-+
[16]张涛,杨振强,王晓旭.应用eQEP及编码器测量电机位置与速度的方法[J],电气传动,2011,4:48-51
[17]韩美佳,杨振强,刘忠伟.感应电动机转子磁通观测的一种方法[J],微特电机,2011,39(2):30-32
[18]王晓旭,杨振强,张涛.基于ATmega48的电动轮椅主从控制系统设计[J],电机技术,2010,4:47-50
[19]张永顺,于宏海,王楠,杨振强,郭东明.胶囊式微型机器人驱动转矩的研究[J],机器人,2008,30(6):516-520,527
[20]姜瑜,杨振强.基于DSP的死区效应补偿方法[J],仪器仪表学报,2006,27(z1):873-874
[21]姜瑜,杨振强.基于DSP的死区效应补偿方法[A],中国仪器仪表学会第八届青年学术会议,2006,873-874
[22]梁天,杨振强.基于VB的DSP与PC机的串行通信[J],微机发展,2005,15(9):96-98
[23]王兴,杨振强.基于DSP的电压空间矢量控制系统在VRV空调中的应用[J],机电信息,2005,13:48-51
[24]骆骄,杨振强.基于ATmega8的新型电动自行车调速控制系统设计[J],国外电子元器件,2005,5:17-19
[25]倪丽琴,杨振强.采用双闭环控制的充电器设计[J],电工技术,2005,2:58-59
[26]杨振强,程树康,朴营国.二级倒立摆的递阶模糊神经网络控制[J],电机与控制学报,2002,6(3):245-248
[27]杨振强,程树康,王志刚.用描述函数分析模糊控制系统的稳定性[J],系统仿真学报,2002,14(4):514-515,521
京公网安备 11010802027423号