近期论文
查看导师新发文章
（温馨提示：请注意重名现象，建议点开原文通过作者单位确认）
Weihang Lu, Qi An*, Cunyu Wang, Shuai Wang, Lujun Huang*, Fengbo Sun, Run Chen, Lin Geng. Sub-micron grains and excellent mechanical properties of low-density Ti40Nb30Mo30-C refractory complex concentrated alloy reinforced with in-situ (Ti, Nb)C. Materials Science and Engineering: A, 2022, 860: 144335. 6 December 2022,
X.T. Li#, Q. An#*, L.J. Huang*, R. Zhang, X. Chen, R. Chen, F.B. Sun, L.Geng. The hot corrosion behaviors and mechanisms of hot-dipped Ti-Al-Si coatings on TiBw/Ti6Al4V composite against NaCl and Na2SO4. Journal of Alloys and Compounds, 2022, 921: 166151. 15 November
Y. Jiao*, C.F. Liu, X.P. Cui, J. Zhang, L.J. Huang, L. Geng. A new approach for measurement of the low-temperature specific heat capacity. Measurement. 2022, 203: 111892. 15 November,IF5.131
Shuai Wang, Lujun Huang*, Rui Zhang, Qi An*, Fengbo Sun, Fanchao Meng, Lin Geng. Effects of rolling deformation on microstructure orientations and tensile properties of TiB/(TA15-Si) composites. Materials Characterization. 2022, 194: 112425. December
Cunyu Wang, Qi An*, Lujun Huang*, Rui Zhang, Xin Chen, Run Chen, Lin Geng, Hua-Xin Peng. Achieving superior strength-ductility synergy by constructing network microstructure in Ti-based high-entropy alloy matrix composites. Composites Communications, 2022, 36: 101357. December
Shuai Wang*, LuJun Huang*, Qi An, ZiShuo Ma, Rui Zhang, Hua-Xin Peng, Lin Geng. Strength-ductility synergy of in-situ TiB/Ti6Al4V composites with tailored hierarchical TiB distributions. Ceramics International. 2022, 48(23): 35069-35075. 1 December
Rui Zhang, Shuai Wang, Xin Chen, Qi An, Lujun Huang*, Lin Geng, Fei Yang*. Significantly enhanced superplasticity of TiBw/near-α Ti composite: Microstructure tailoring and deformation mechanisms. Materials Science and Engineering: A. 2022, 853: 143772. 15 September
Shuai Wang*, Qi An, WenQi Liu, Rui Zhang, ZiShuo Ma, LuJun Huang*, Lin Geng. Towards strength-ductility enhancement of titanium matrix composites through heterogeneous grain structured Ti matrix design. Journal of Alloys and Compounds. 2022, 927: 167022. 15 December
Shuai Wang*, LuJun Huang*, BaoXi Liu, Hua-Xin Peng, Yang Jiao, Lin Geng. Microstructure and mechanical properties of Ti6Al4V based laminated composites at various rolling reductions. Composites Communications. 2022, 33: 101212. August
Laibo Sun, Chunhuan Guo, Lujun Huang, Fengchun Jiang, Kai Xu, Ruisheng Huang*. Effect and mechanism of inter-layer ultrasonic impact strengthening on the anisotropy of low carbon steel components fabricated by wire and arc additive manufacturing. Materials Science and Engineering: A. 2022, 848: 143382. 19 July
Qi An, Shuai Wang, Lujun Huang*, Cunyu Wang, Qi Qian, Yong Jiang, Liqin Wang, Lin Geng*. Experimental and first-principles study on TiB/TiC interface in hybrid (TiB%2BTiC)/Ti6Al4V composite. Ceramics International. 2022, 48(15): 22554-22559. 1 August
Run Chen, Qi An*, Shuai Wang, Lujun Huang*, Rui Zhang, Cunyu Wang, Shipeng Zhou, LinGeng. Overcoming the strength-ductility trade-off dilemma in TiBw/TC18 composites via network architecture with trace reinforcement. Materials Science and Engineering: A. 2022, 842: 143092. 11 May
Qi An, Lujun Huang, Qi Qian, Yong Jiang, Shuai Wang, Rui Zhang, Lin Geng, Liqin Wang. Insights into in-situ TiB/dual-phase Ti alloy interface and its high load-bearing capacity. Journal of Materials Science & Technology. 2022, 119: 156-166. 20 August
Xuefeng Zhou, Cong Gao, Dandan Wang, Shang Peng, Lujun Huang, Wengge Yang, Wen-Hua Zhang*, Xiang Gao*. Revealing the dominant factor of domain boundary resistance on bulk conductivity in lanthanum lithium titanates. J. Energy Chem. 2022, 73, 354-359. IF = 13.599 18 June
Shuai Wang, Qi An, Rui Zhang, Shan Jiang, Lujun Huang, Run Chen, Baoxi Liu, Yang Jiao, Lin Geng. Microstructure characteristics and enhanced properties of network-structured TiB/(TA15-Si) composites via rolling deformation at different temperatures. Materials Science and Engineering: A, 2022, 829: 142176
Shiyang Wang, Sheng Zhan, Xingyu Hou, Long Wang, Hongwei Zhang, Hongyu Zhang, Yuan Sun, Lujun Huang. Microstructure and Mechanical Property of a Multi-Scale Carbide Reinforced Co-Cr-W Matrix Composites. Crystals. 2022, 12: 198.
Hao Ding, Xiping Cui* Yuchen Wang, Delong Cai, Zhiqi Wang, Yuanyuan Zhang, Lujun Huang*, Lin Geng. A feasible surface patterning method for SEM-DIC: Achieving high-resolution in-situ mapping of local strain and microstructure to reveal the effect of slip transfer on shear strain near grain boundaries, Microscopy and Microanalysis, 2022, 28: 1931–1944. 2022.4.3, IF:4.099
Hao Ding, Xiping Cui*, Zhiqi Wang, Zhao Tao, Yuchen Wang, Yuanyuan Zhang, Hongtao Chen, Lujun Huang*, Lin Geng, Junfeng Chen*. A new strategy for fabrication of unique heterostructured titanium laminates and visually tracking their synchronous evolution of strain partitions versus microstructure, Journal of Materials Science & Technology, 2022, 107: 70-81 (一区，IF: 10.319)
陈润，王帅*，安琦，张芮，刘文齐，黄陆军，耿林. 热挤压与热处理对网状TiBw/TC18复合材料组织及性能的影响. 金属学报(SCI). 2022, 58(11): 1478-1488.
L.J. Huang, Q. An, L. Geng, S. Wang, S. Jiang, X.P. Cui, R. Zhang, F.B. Sun, Y. Jiao, X. Chen, C.Y. Wang. Multi-scale Architecture and Superior High-temperature Performances of Discontinuously Reinforced Titanium Matrix Composites. Advanced Materials, 2021, 33(6), 2000688 IF： 30.849
Shan Jiang, Lujun Huang, Xiang Gao, Gang Liu, Rui Zhang, Yang Jiao, Shang Peng, Qi An, Shuai Wang, Lin Geng. Interstitial carbon induced FCC-Ti exhibiting ultrahigh strength in a Ti37Nb28Mo28-C7 complex concentrated alloy. Acta Materialia, 2021, 203: 116456. IF 7.656
Hao Ding, Xiping Cui, Naonao Gao, Yuan Sun, Yuanyuan Zhang, Lujun Huang, Lin Geng. Fabrication of (TiB/Ti)-TiAl composites with a controlled laminated architecture and enhanced mechanical properties. Journal of Materials Science and Technology. 2021, 62: 221-233. IF：6.155
Shuai Wang, Lujun Huang, Shan Jiang, Rui Zhang, Baoxi Liu, Fengbo Sun, Qi An, Yang Jiao, Lin Geng. Microstructure evolution and tensile properties of as-rolled TiB/TA15 composites with network microstructure, Materials Science and Engineering: A, 15 February 2021, 804: 140783
Xin Chen, Lujun Huang, Yang Jiao, Shuai Wang, Qi An, Yang Bao, Lin Geng. Mechanisms of oxidation anisotropy between a-Ti (0001) and (01-10) crystallographic planes in titanium matrix composites. Materials Letters, 2021, 286: 129230
Ming Ji, Lujun Huang, Qi An, Yang Bao, Xiping Cui, Yang Jiao, Lin Geng. Microstructure refinement and strengthening mechanisms of network structured TiBw/Ti6Al4V composites by TIG remelting. Materials Science and Engineering A, 2021, 804, 140755
Yang Bao, Lujun Huang, Shan Jiang, Rui Zhang, Qi An, Caiwei Zhang, Lin Geng, Xinxin Ma. A novel Ti cored wire developed for wire-feed arc deposition of TiB/Ti composite coating. Journal of Materials Science & Technology, 2021, 83: 145–160.
Shuai Wang, Lujun Huang, Shan Jiang, Rui Zhang, Fengbo Sun, Qi An, Lin Geng. Multiplied bending ductility and toughness of titanium matrix composites by laminated structure manipulation. Materials & Design, 2021, 197: 109237
Shuai Wang, Qi An, Rui Zhang, XiPing Cui, LuJun Huang, Lin Geng. Strain rate sensitivity of titanium matrix composites: In the presence of laminated structure. Composites Communications, 2021, 26: 100787.
Shan Jiang, Qi An, Xiping Cui, Xuelian Xiang, Lujun Huang, Rui Zhang, Yuan Sun, Lin Geng. Fabrication and mechanical properties of the titanium matrix composites based on Ti6Al4V-ZrB2-(Si) system. Materials Science and Engineering: A, 2021, 819: 141488
Xin Chen, Qi An, Shan Jiang, Yang Jiao, Lujun Huang, Lin Geng. Revealing Anti-oxidation Mechanisms of Titanium Composite Materials by Detailed Characterization of Scale Phase Constitutions[J]. Corrosion Science, 2021, 192: 109845.
Zhang R, Huang L, Zhao X, et al. Influence of deformation parameters and network structure to the microstructure evolution and flow stress of TiBw/Ti64 composite[J]. Materials Science and Engineering: A, 2021, 809: 140997.
Yanan Gao, Lujun Huang, Yang Bao, Qi An, Yuan Sun, Rui Zhang, Lin Geng, Jie Zhang. Joints of TiBw/Ti6Al4V composites- Inconel 718 alloys dissimilar joining using Nb and Cu interlayers. Journal of Alloys and Compounds, 2020, 822: 153559
Shuai Wang, LuJun Huang, Lin Geng, Yuan Sun, Hua-Xin Peng, ShaoXing Qu. Microstructure evolution and damage mechanism of layered titanium matrix composites under tensile loading. Materials Science & Engineering A, 2020, 777: 139067
Shuai Wang, Lujun Huang, Shan Jiang, Rui Zhang, Qi An, Yuan Sun, Lin Geng. Microstructure evolution and improved properties of laminated titanium matrix composites with gradient equiaxed grains. Science China Technological sciences, 2020, 63: 2687-2697.
Qi An, Lujun Huang, Shan Jiang, Shuai Wang, Rui Zhang, Fengbo Sun, Atieh Moridi, Lin Geng. Wear rate of titanium matrix composite coating at high temperature further increased by non-stoichiometric TixC oxidation. Ceramics International, 2020, 46: 8068-8074.
Fengbo Sun, Lujun Huang, Rui Zhang, Shuai Wang, Shang Jiang, Yuan Sun, Qi An, Yang Jiao, Lin Geng. In-situ synthesis and superhigh modulus of network structured TiC/Ti composites based on diamond-Ti system. Journal of Alloys and Compounds, 2020, 834: 155248
Shan Jiang, Lujun Huang, Qi An, Xiang Gao, Shuai Wang, Lin Geng, Rui Zhang, Fengbo Sun, Yang Jiao. Significantly strengthening the Ti70Nb10Mo10Zr10 alloy via architecting two-scale silicide reinforcement. Journal of Alloys and Compounds, 2020, 835: 155255
黄陆军, 孙枫泊, 安琦, 韩亚坤, 刘悦, 崔喜平, 耿林. (TiBw%2B(TiZr)5Si3)/ TA15 钛基复合材料粉末冶金制备与热处理改性. 中国科学技术科学. 2020, 50(7): 935-946.
Yang Bao, Lujun Huang, Qi An, Shan Jiang, Rui Zhang, Lin Geng, Xinxin Ma. Insights into arc-assisted self-propagating high temperature synthesis of TiB2-TiC ceramic coating via wire-arc deposition. Journal of the European Ceramic Society, 2020, 40: 4381-4395.
Qi An, Ahmed Elshafiey, Lujun Huang, David A. Hammer, Mostafa Hassani. Plasma and X-ray Radiation-Induced Damage Mechanisms in a Tungsten Heavy Alloy. Journal of Nuclear Materials. 2020, 539: 152325
郑俊超，黄陆军，马瑞，白洁，张芮，姜山，耿林. 热处理对网状结构TiBw/TA15(Mo,Si)复合材料组织与性能的影响. 航空材料学报, 2020, 40(3)： 118-126.
Xiping Cui, Hao Ding, Yuanyuan Zhang, Yao Yao, Guohua Fan, Lujun Huang, Lin Geng, Zhenzhu Zheng, Junfeng Chen. Fabrication, microstructure characterization and fracture behavior of a unique micro-laminated TiB-TiAl composites. Journal of Alloys and Compounds, 2019, 775: 1057-1067.
Qi An, Lujun Huang, Yang Jiao, Yang Bao, Bo Zhong, Lin Geng. Intergrowth microstructure and superior wear resistance of (TiB？%2B？TiC)/Ti64 hybrid coatings by gas tungsten arc cladding. Materials & Design, 2019, 162: 34-44.
Shaolou Wei, Lujun Huang, Yuntong Zhu, Zhe Shi, Xinting Li and Lin Geng. Sub-stoichiometry-facilitated oxidation kinetics in a δ-TixC doped Ti-based alloy. npj materials degradation, 2019, 3:3
Y. Jiao, L.J. Huang, S.L. Wei, H.X. Peng, Q. An, S. Jiang, L. Geng. Constructing two-scale network microstructure with nano-Ti5Si3 for superhigh creep resistance. Journal of Materials Science & Technology, 2019, 35: 1532-1542.
Shuai Wang, LuJun Huang, Rui Zhang, BaoXi Liu, XiPing Cui, Lin Geng, Hua-Xin Peng. Enhancing ductility of titanium matrix composites by multimodal α-grains，Scripta Materialia. 2019, 170: 161-165.
Shaolou Wei, Lujun Huang, Xinting Li, Yang Jiao, Wei Ren, Lin Geng. Network-strengthened Ti-6Al4V/(TiC%2BTiB) Composites: Powder Metallurgy Processing and Enhanced Tensile Properties at Elevated Temperatures. Metallurgical and Materials Transactions A, 2019, 50: 3629-3645.
Yang Bao, LujunHuang, Qi An, Shan Jiang, Rui Zhang, Lin Geng, Xinxin Ma. Metal transfer and microstructure evolution during wire-feed deposition of TiB/Ti composite coating. Journal of Materials Processing Technology, 2019, 274: 116298.
Qi An, Lujun Huang, Shaolou Wei, Lin Geng. Corrosion Science, 2019, 158: 108102.
X.T. Li, L.J. Huang, S. Jiang, Y.N. Gao, Q. An, S.Wang, R. Zhang, L. Geng. Microstructure and super oxidation resistance of the network structured Ti-Al-Si coating. Journal of Alloys and Compounds, 2019, 807: 151679
Rui Zhang, Lujun Huang, Qi An, Lin Geng, Bo Wang, Yang Jiao. The hyperbolic constitutive equations and modified dynamic material model of TiBw/Ti-6.5Al-2.5Zr-1Mo-1V-0.5Si composites. Materials Science and Engineering: A, 2019, 766: 138329.
Y. Jiao, L.J. Huang, L. Geng, R. Zhang, S. Jiang, X.T. Li, Y.N. Gao. Strengthening and plasticity improvement mechanisms of titanium matrix composites with two-scale network microstructure, Powder Technology, 2019, 356: 980-989.
Shuai Wang, LuJun Huang, Qi An, Shan Jiang, Rui Zhang, Lin Geng, ShaoXing Qu, HuaXin Peng. Regulating crack propagation in laminated metal matrix composites through architectural control. Composites Part B, 2019, 178: 107503.
Yanan Gao, Lujun Huang, Yuan Sun, Qi An, Jie Zhang, Lin Geng. Interfacial reaction mechanism of TiBw/Ti6Al4V Composites and Inconel 718 alloys by GTAW heat transmission, Science China Technological Sciences, 2019, 62: 2293-2301.
Xiping Cui, Yuanyuan Zhang, Yao Yao, Hao Ding, Lin Geng, Lujun Huang, Yuan Sun. Synthesis and fracture characteristics of TiB2–TiAl composites with a unique microlaminated architecture. Metallurgical and Materials Transactions A, 2019, 50: 5853-5865
黄陆军，耿林，彭华新，钛合金与钛基复合材料第二相强韧化，中国材料进展，2019，38(3) :214-222 Lujun Huang, Lin Geng, Huaxin Peng. Strengthening and toughening mechanisms of the second phase in titanium alloys and titanium matrix composites. Materials China (In Chinese). 2019, 38: 214-222.
Lujun Huang, Tianbo Duan, Qi An, Youyou Chen, Jiuyang Bai, Lin Geng & Sanbao Lin. Gas tungsten arc welding of network structured titanium matrix composite, Science and Technology of Welding and Joining, 2018, 23(5): 357-364.
S. Wang, L.J. Huang, Q. An, L. Geng, B.X. Liu. Dramatically enhanced impact toughness of two-scale laminate-network structured composites. Materials and Design, 2018,140: 163-171.
Qi An, L.J. Huang*, Yang Bao, Rui Zhang, Shan Jiang, Lin Geng*, Miaomiao Xiao, Dry sliding wear characteristics of in-situ TiBw/Ti6Al4V composites with different network parameters, Tribology International, 2018, 121: 252-259.
S. Jiang, L.J. Huang, Q. An, L. Geng, X.J. Wang, S. Wang, Study on Titanium-Magnesium Composites with Bicontinuous Structure Fabricated by Powder Metallurgy and Ultrasonic Infiltration, Journal of the Mechanical Behavior of Biomedical Materials, 2018, 81: 10-15
X.T. Li, L.J. Huang, S.L. Wei, Q. An, X.P. Cui, L. Geng. Cycle oxidation behavior and anti-oxidation mechanism of hot-dipped aluminum coating on TiBw/Ti6Al4V composites with network microstructure. Scientific Reports. 2018, 8: 5790.
S.L. Wei, L.J. Huang, X.T. Li, Q. An, L. Geng, Interactive effects of cyclic oxidation and structural evolution for Ti-6Al-4V/(TiC%2BTiB) alloy composites at elevated temperatures, Journal of Alloys and Compounds, 2018, 752: 164-178
Qi An, Lujun Huang, Shan Jiang, Yang Bao, Ming Ji, Rui Zhang, Lin Geng, Two-scale TiB/Ti64 composite coating fabricated by two-step process. Journal of Alloys and Compounds 2018, 755: 29-40.
Y. Jiao, L.J. Huang, S.L. Wei, L. Geng, M.F. Qian, S. Yue. Nano-Ti5Si3 leading to enhancement of oxidation resistance. Corrosion Science. 2018, 140： 223-230
Yanan Gao, Lujun Huang, Qi An, Yang Bao, Xinting Li, Jie Zhang, Lin Geng. Microstructure Evolution and Mechanical Properties of Titanium Matrix Composites and Ni-based Superalloy Joints with Cu interlayer. Journal of Alloys and Compounds. 2018, 764: 665-673.
Yang Bao, Lujun Huang, Qi An, Shan Jiang, Lin Geng, Xinxin Ma. Wire-feed deposition TiB reinforced Ti composite coating: formation mechanism and tribological properties. Materials Letters, 2018, 229: 221-224.
Y. Jiao, L.J. Huang, L. Geng, Progress on discontinuously reinforced titanium matrix composites. Journal of Alloys and Compounds. 2018, 767: 1196-1215.
Wang B, Zhang HB, Huang LJ, He JL, Zhang YF, Wang W. Evolution of microstructure and high temperature tensile properties of as-extruded TiBw reinforced near- titanium matrix composite subjected to heat treatments. Science China-Technological Sciences, 2018, 61(9): 1340-1345.
Y. Jiao, L.J. Huang*, L. Geng, X.T. Li, Y.N. Gao, M.F. Qian, R. Zhang. Nano-scaled Ti5Si3 Evolution and Strength Enhancement of Titanium Matrix Composites with Two-scale Architecture via Heat Treatment. Materials Science and Engineering: A, 2017, 701: 359-369.
R. Zhang, D.J. Wang*, L.J. Huang, S.J. Yuan, L. Geng. Deformation behaviors and microstructure evolution of TiBw/TA15 composite with novel network architecture. Journal of Alloys and Compounds, 2017, 722: 970-980.
B. Wang, L.J. Huang*, L. Geng, Z.S. Yu. Modification of microstructure and tensile property of TiBw/near-α Ti composites by tailoring TiBw distribution and heat treatment. Journal of Alloys and Compounds. 2017, 690: 424–430.
B.X. Liu, L.J. Huang*, B. Kaveendran, L. Geng, X.P. Cui, S.L. Wei, F.X. Yin. Tensile and bending behaviors and characteristics of laminated Ti-(TiBw/Ti) composites with different interface status. Composites Part B, 2017, 108: 377-385
R. Zhang, D.J. Wang*, L.J. Huang, S.J. Yuan. Effects of heat treatment on microstructure and high temperature tensile properties of TiBw/TA15 composite billet with network architecture. Materials Science and Engineering: A, 2017, 679: 314-322
S. Wang, L.J. Huang*, L. Geng*, F. Scarpa, Y. Jiao, H. X. Peng. Significantly enhanced creep resistance of low volume fraction in-situ TiBw/Ti6Al4V composites by architectured network reinforcements. Sci. Rep./Scientific Reports, 2017, 7: 40823
Y. Jiao, L.J. Huang*, S. Wang, X.T. Li, Q. An, X.P. Cui*, L. Geng. Effects of first-scale TiBw on secondary-scale Ti5Si3 characteristics and mechanical properties of in-situ (Ti5Si3%2BTiBw)/Ti6Al4V composites. Journal of Alloys and Compounds, 2017, 704: 269-281.
Q. An, L.J. Huang, S. Jiang, X.T. Li, Y.N. Gao, Y. Liu, L. Geng, Microstructure evolution and mechanical properties of TIG cladded TiBw reinforced composite coating on Ti-6Al-4V alloy. Vacuum, 2017, 145: 312-319.
Peng Wang, Guodong Nian and Shaoxing Qu, Yejie Shan, Lujun Huang, Hua-Xin Peng. Numerical Study on Mechanical Properties of Discontinuously Reinforced Titanium Matrix Composite with Network Reinforcement Architecture. International Journal of Applied Mechanics, 2017, 9(5): 1750073
L.J. Huang*, C.J. Lu, B.Yuan, S.L. Wei, X.P. Cui*, L. Geng, Comparative study on superplastic tensile behaviors of the as-extruded Ti6Al4V alloys and TiBw/Ti6Al4V composites with tailored architecture, Materials and Design, 2016, 93: 81-90. 3.997
Y. Jiao, L J Huang*, T B Duan, S. L. Wei, K. Balasubramaniam, L. Geng. Controllable two-scale network architecture and superior mechanical properties of (Ti5Si3%2BTiBw)/Ti6Al4V composites. Scientific Reports [J], 2016, 6:32991.
Y. Jiao, L.J. Huang*, Q. An, S. Jiang, Y.N. Gao, X.P. Cui*, L. Geng. Effects of Ti5Si3 characteristics adjustment on microstructure and tensile properties of in-situ (Ti5Si3%2BTiBw)/Ti6Al4V composites with two-scale network architecture. Materials Science & Engineering A 2016, 673:595-605
B.X. Liu, L.J. Huang*, X.D. Rong, L. Geng, F.X. Yin, Bending behaviors and fracture characteristics of laminated ductile-tough composites under different modes. Composites Science and Technology. 2016, 126: 94-105. 3.897
S.L. Wei, L.J. Huang*, J. Chang, W. Zhai, S.J. Yang, L. Geng, Primary phase growth and microstructure evolution of rapidly solidifying ternary Ti-12Al-8V alloy. Materials Letters, 2016, 175: 291-295. 2.437
Xiping Cui*, Guohua Fan*, Lujun Huang, Jinxin Gong, Hao Wu, Tongtong Zhang, Lin Geng, Songhe Meng. Preparation of a novel layer-structured Ti3Al matrix composite sheet by liquid–solid reaction between Al foils and TiB/Ti composite foils. Materials and Design, 2016, 101: 181-187.
魏绍楼，黄陆军*，常健，杨尚京，耿林. 液态Ti-Al 合金的深过冷与快速枝晶生长. 物理学报. 2016, 65(9): 096101. Wei Shao-Lou, Huang Lu-Jun, Chang Jian, Yang Shang-Jing, Geng Lin. Substantial undercooling and rapid dendrite growth of liquid Ti-Al alloy. Acta Physica Sinica. 2016, 65(9): 096101.
H.T. Hu, L.J. Huang, L. Geng*, J.F. Sun, H. Tian. High temperature mechanical properties of as-extruded TiBw/Ti60 composites with ellipsoid network architecture. Journal of Alloys and Compounds. 2016, 688: 958–966.
H.T. Hu, L. Geng, L.J. Huang, C.Y. Li, High temperature mechanical properties of 3D network structured TiBw/Ti60 composite. Rare Metal Materials and Engineering. 2016, 45(12): 3278-3283. 胡海亭*，耿林，黄陆军，李春雨. 3D网状结构TiBw/Ti60复合材料高温力学性能, 稀有金属材料与工程. 2016年12月, 45(12): 3278-3283.
黄陆军，耿林*. 网状结构钛基复合材料研究进展, 中国材料进展, 2016, 35(9): 674-685第一标注51471063，51271064
B.X. Liu, L. Geng, X.L. Dai, F.X. Yin, L.J. Huang, Multiple Toughening Mechanisms of Laminated Ti-TiBw/Ti Composites Fabricated by Diffusion Welding. Materials Science Forum, 2016, 848: 196-201. 2016.03
L.J. Huang*, L. Geng and H.X. Peng*%2B. Microstructurally Inhomogeneous Composites: Is a homogeneous reinforcement distribution optimal? Progress in Materials Science. 2015, 71: 93-168.
B. Wang, L.J. Huang*, L. Geng, X.D. Rong, B.X. Liu. Effects of heat treatments on microstructure and tensile properties of as-extruded TiBw/near-α Ti composites. Materials and Design. 2015, 85(15): 679-686.
B. Wang, L.J. Huang, L. Geng*, X.D. Rong. Compressive behaviors and mechanisms of TiB whiskers reinforced High temperature Ti60 alloy matrix composites. Materials Science and Engineering A, 2015, 648: 443-451.
B. Wang, L.J. Huang, H.T. Hu, B.X. Liu, L. Geng*, Superior tensile strength and microstructure evolution of TiB whisker reinforced Ti60 composites with network architecture after β extrusion. Materials Characterization, 2015, 103: 140-149.
B. Wang, L.J. Huang, B.X. Liu, L. Geng*, H.T. Hu. Effects of deformation conditions on the microstructure and substructure evolution of TiBw/Ti60 composite with network structure. Materials Science and Engineering: A, 2015, 627(11): 316-325.
C.J. Lu, L.J. Huang, L. Geng*, B. Kaveendran, Z.Z. Zheng, J. Zhang. Mechanisms behind the superplastic behavior of as-extruded TiBw/Ti6Al4V composites with a network architecture. Materials Characterization. 2015, 104: 139-148.
C. Liu, L.J. Huang, L. Geng*, Y. Jiao, A. Tang. In Situ Synthesis of (TiC%2BTi3SiC2%2BTi5Si3)/Ti6Al4V Composites with Tailored Two-scale Architecture. Advanced Engineering Materials. 2015, 17(7): 933-941.
LIU Baoxi, HUANG Lujun, GENG Lin*. Elastic and Plastic Behaviors of Laminated Ti-TiBw/Ti Composites. Journal of Wuhan University of Technology. 2015, 30(3): 596-600.
戎旭东, 黄陆军, 王博, 唐骜, 耿林, 热处理对魏氏组织Ti60合金组织与性能的影响, 材料热处理学报. 2015, 36(10): 39-45.
戎旭东, 黄陆军，王 博，唐 骜, 耿林, 热处理对网状结构TiBw/Ti60复合材料组织与性能影响, 复合材料学报, 2015, 32(6): 1729-1736.
H.T. Hu, L.J. Huang, L. Geng*, C. Liu, B.X. Liu, B. Wang. Oxidation behavior of TiB-whisker-reinforced Ti60 alloy composites with three-dimensional network architecture. Corrosion Science, 2014, 85: 7-14.
黄陆军, 耿林*. 非连续增强钛基复合材料研究进展. 航空材料学报. 2014, 34(4): 126-138.
Lin Geng*, Lujun Huang. High Temperature Properties of Discontinuously Reinforced Titanium Matrix Composites: A Review. Acta Metall. Sin. (Engl. Lett.), 2014, 27(5), 787-797.
H.T. Hu, L.J. Huang, L. Geng*, C. Liu, B. Wang, Effects of extrusion on microstructure and tensile properties of 3D network structured TiBw/Ti60 composites fabricated by reaction hot pressing, Journal of Alloys and Compounds, 2014, 582: 569-575.
B.X. Liu, L.J. Huang, L. Geng*, B. Wang, C. Liu, W.C. Zhang, Fabrication and superior ductility of laminated Ti–TiBw/Ti composites by diffusion welding. Journal of Alloys and Compounds, 2014, 602(25): 187-192.
B.X. Liu, L.J. Huang, B. Wang, L. Geng*. Effect of pure Ti thickness on the tensile behavior of laminated Ti–TiBw/Ti composites. Materials Science and Engineering A. 2014, 617(3): 115-120.
B.X. Liu, L.J. Huang, L. Geng*, B. Wang, X.P. Cui. Fracture behaviors and microstructural failure mechanisms of laminated Ti-TiBw/Ti composites. Materials Science and Engineering A. 2014, 611: 290-297.
B.X. Liu, L.J. Huang, L. Geng*, B. Wang, X.P. Cui. Effects of reinforcement volume fraction on tensile behaviors of laminated Ti-TiBw/Ti composites. Materials Science and Engineering A. 2014, 610: 344-349.
B.X. Liu, L.J. Huang, L. Geng*, B. Kaveendran, B. Wang, X.Q. Song, X.P. Cui. Gradient grain distribution and enhanced properties of novel laminated Ti-TiBw/Ti composites by reaction hot-pressing. Materials Science and Engineering A. 2014; 595: 257-265.
El Oualid Mokhnache, guisong WANG, lin Geng*, lujun Huang. Microstructures and Mechanical Properties of In Situ Al2O3/Al-Si Composites Fabricated by Reaction Hot Pressing. Metallurgical and Materials Transactions B, 2014, 45(6): 1965 -1969.
El Oualid Mokhnache, Guisong Wang, Lin Geng*, Balasubramaniam Kaveendran, Lujun Huang. Synthesis and Characterization of In Situ (Al2O3–Si)/Al Composites by Reaction Hot Pressing. Acta Metall. Sin. (Engl. Lett.) 2014, 27(5): 930-936.
L.J. Huang, S. Wang, L. Geng*, B. Kaveendran, H.X. Peng%2B, Low volume fraction in situ (Ti5Si3%2BTi2C)/Ti hybrid composites with network microstructure fabricated by reaction hot pressing of Ti-SiC system, Composites Science and Technology, 2013, 82: 23-28.
L.J. Huang, L. Geng*, Y. Fu, B. Kaveendran, H.X. Peng%2B, Oxidation behavior of in situ TiCp/Ti6Al4V composite with self-assembled network microstructure fabricated by reaction hot pressing, Corrosion Science, 2013, 69: 175-180.
L.J. Huang, L. Geng*, B. Wang, L.Z. Wu*, Effects of volume fraction on the microstructure and tensile properties of in situ TiBw/Ti6Al4V composites with novel network microstructure, Materials and Design, 2013, 45: 532-538.
L.J. Huang, F.Y. Yang, H.T. Hu, X.D. Rong, L. Geng*, L.Z. Wu*, TiB whiskers reinforced high temperature titanium Ti60 alloy composites with novel network microstructure, Materials and Design, 2013, 51: 421-426.
L.J. Huang, Y.Z. Zhang, B.X. Liu, X.Q. Song, L. Geng*, L.Z. Wu*, Superplastic tensile characteristics of in situ TiBw/Ti6Al4V composites with novel network microstructure, Materials Science and Engineering A, 2013, 581, 128-132.
L.J. Huang, Y.Z. Zhang, L. Geng*, B. Wang, W. Ren, Hot compression characteristics of TiBw/Ti6Al4V composites with novel network microstructure using processing maps, Materials Science and Engineering A, 2013, 580: 242-249.
Lujun Huang, Yuzi Zhang, Lin Geng*. Hot simulation compression of in situ TiBw/Ti6Al4V composites with novel network microstructure. Materials Science Forum. 2013, 762: 382-386.
B.X. Liu, L.J. Huang, L. Geng*, B. Wang, X.P. Cui, C. Liu, G.S, Wang, Microstructure and tensile behavior of novel laminated Ti-TiBw/Ti matrix composite by reaction hot pressing, Materials Science and Engineering A, 2013, 583: 182-187.
B. Kaveendran, G.S. Wang, L.J. Huang, L. Geng*, H.X. Peng%2B, In situ (Al3Zr %2B Al2O3np)/2024Al metal matrix composite with novel reinforcement distributions fabricated by reaction hot pressing, Journal of Alloys and Compounds, 2013, 581: 16-22.
黄陆军, 唐骜, 戎旭东, 耿林*, 热轧制变形对网状结构TiBw/Ti6Al4V复合材料组织与性能的影响, 航空材料学报, 2013, 33(2): 8-12.
黄陆军，唐骜，胡悦，陆成杰，耿林*. 热压烧结制备调控组织TiBw/Ti复合材料. 中国有色金属学报, 2013, 23(s1): s696-s701.
许虹宇, 黄陆军, 耿林*, 张 杰, 黄玉东, Cu含量对Al2O3·SiO2sf /Al-Cu复合材料耐磨性能的影响, 金属学报, 2013, 49(9): 1131-1136.
唐骜，黄陆军，刘宝玺，戎旭东，耿林*. 增强体含量对TiBw/Ti复合材料组织与力学性能的影响. 复合材料学报. 2013, 30(s1): 90-95.
L.J. Huang, L. Geng*, B. Wang, H.Y. Xu, B. Kaveendran, Effects of extrusion and heat treatment on the microstructure and tensile properties of in situ TiBw/Ti6Al4V composite with a network architecture, Composites: Part A, 2012, 43(3): 486-491.
L.J. Huang, H.Y. Xu, B. Wang, Y.Z. Zhang, L. Geng*, Effects of heat treatment parameters on the microstructure and mechanical properties of in situ TiBw/Ti6Al4V composite with a network architecture, Materials and Design, 2012, 36: 694-698.
L.J. Huang, L. Geng*, H.X. Peng%2B, B. Kaveendran, High temperature tensile properties of in situ TiBw/Ti6Al4V composites with a novel network reinforcement architecture, Materials Science and Engineering A, 2012, 534(1): 688-692.
L.J. Huang, S. Wang, Y.S. Dong, Y.Z. Zhang, F. Pan, L. Geng*, H.X. Peng%2B, Tailoring a novel network reinforcement architecture exploiting superior tensile properties of in situ TiBw/Ti composites, Materials Science and Engineering A, 2012, 545: 187-193.
HUANG Lu-Jun, CUI Xi-ping, GENG Lin*, FU Yu, Effects of rolling deformation on microstructure and mechanical properties of network structured TiBw/Ti composites, Trans. Nonferrous Met. Soc. China, 2012, 22: s79-s83.
B. Wang, L.J. Huang, L. Geng*, Effects of heat treatments on the microstructure and mechanical properties of as-extruded TiBw/Ti6Al4V composites, Materials Science and Engineering A, 2012, 558: 663-667.
ZHANG Yu-Zi, HUANG Lu-Jun, LIU Bao-Xi, GENG Lin*, Hot deformation behavior of in-situ TiBw/Ti6Al4V composite with a novel network reinforcement distribution, Trans. Nonferrous Met. Soc. China, 2012, 22: s465-s471.
Xiping Cui, Guohua Fan, Lin Geng*, Yin Wang, Lujun Huang, Hua-Xin Peng%2B, Growth kinetics of TiAl3 layer in multi-laminated Ti-(TiB2/Al) composite sheets during annealing treatment, Materials Science and Engineering A, 2012, 539: 337-343.
L.J. Huang, L. Geng*, H.X. Peng%2B, J. Zhang, Room Temperature Tensile Fracture Characteristics of in situ TiBw/Ti6Al4V Composites with a Quasi-continuous Network Architecture, Scripta Materialia, 2011, 64(9): 844-847.
L.J. Huang, L. Geng*, H.X. Peng%2B, K. Balasubramaniam, G.S. Wang, Effects of Sintering Parameters on the Microstructure and Tensile Properties of in situ TiBw/Ti6Al4V Composites with a Novel Network Architecture, Materials and Design, 2011, 32(6): 3347-3353.
L.J. Huang, L. Geng*, H.Y. Xu, H.X. Peng%2B, In situ TiC Particles Reinforced Ti6Al4V Matrix Composite with a Network Reinforcement Architecture, Materials Science and Engineering A, 2011, 528(6): 2859-2862.
F.Y. Yang, A.B. Li, L.J. Huang, Y. Cheng, L. Geng*, Study on the fabrication and heat treatment of the sheet material of in situ TiBw/Ti60 composites, RARE METALS, 2011, 30: 614-618.
Li-na GUAN, Lin GENG*, Hong-wei ZHANG, Lu-jun HUANG, Effects of stirring parameters on microstructure and tensile properties of (ABOw%2BSiCp)/6061Al composites fabricated by semi-solid stirring technique, Trans. Nonferrous Met. Soc. China, 2011, 21(2): 274-279.
Ce LIANG, Feng LI, Lin GENG*, Lu-jun HUANG, Fabrication of Ti-Al complex with superior deformation capability by pressure infiltration, Trans. Nonferrous Met. Soc. China, 2011, 21(2): 358-361
L.J. Huang, L. Geng*, H.X. Peng%2B, In-situ (TiBw%2BTiCp)/Ti6Al4V Composites with a Network Reinforcement Distribution, Materials Science and Engineering A, 2010, 527(24-25): 6723-6727.
B.P. Zhang, L. Geng*, L.J. Huang, X.X. Zhang, C.C. Dong, Enhanced Mechanical Properties in Fine Grained Mg-1.0Zn-0.5Ca Alloys Prepared by Extrusion at Different Temperatures, Scripta Materialia, 2010, 63(10): 1024-1027.
Lin GENG*, Hong-wei ZHANG, Hao-ze LI, Li-na GUAN, Lu-jun HUANG, Effects of Mg content on the microstructure and mechanical properties of SiCp/Al-Mg composites fabricated by semi-solid stirring technique, Transactions of Nonferrous Metals Society of China, 2010, 20(10): 1851-1855.
H.W. Zhang, L. Geng*, L.N. Guan, L.J. Huang, Effects of SiC Particle Pretreatment and Stirring Parameters on the Microstructure and Mechanical Properties of SiCp/Al-6.8Mg Composites Fabricated by Semi-solid Stirring Technique, Materials Science and Engineering A, 2010, 528(1): 513-518.
L.J. Huang, L. Geng*, A.B. Li, F.Y. Yang, H.X. Peng%2B, In situ TiBw/Ti-6Al-4V Composites with Novel Reinforcement Architecture Fabricated by Reaction Hot Pressing, Scripta Materialia, 2009, 60(11): 996-999.
L.J. Huang, L. Geng*, P.Q. Zheng, A.B. Li, X.P. Cui, Hot Tensile Characterization of Ti-6.5Al-3.5Mo-1.5Zr-0.3Si Alloy with an Equiaxed Microstructure, Materials and Design, 2009, 30(3): 838-841.
L.J. Huang, L. Geng*, A.B. Li, X.P. Cui, H.Z. Li, G.S. Wang, Characteristics of Hot Compression Behavior of Ti-6.5Al-3.5Mo-1.5Zr-0.3Si Alloy with an Equiaxed Microstructure, Materials Science and Engineering A, 2009, 505(1-2): 136-143.
Lujun Huang, Fuyao Yang, Y. L. Guo, J. Zhang, L. Geng*, Effect of Sintering Temperature on Microstructure of Ti6Al4V Matrix Composites, International Journal of Modern Physics B, 2009, 23(6-7): 1444-1448.
A.B. Li, L.J. Huang, Q.Y. Meng, L. Geng*, X.P. Cui, Hot Working of Ti-6Al-3Mo-2Zr-0.3Si Alloy with Lamellar α%2Bβ Starting Structure Using Processing Map, Materials and Design, 2009, 30(5): 1625-1631.
P.Q. Zheng, L.J. Huang, A.B. Li, L. Geng*, Lamellar Disintegration Mechanism of TC11 Titanium Alloy during Hot Compression, Journal of Wuhan University of Technology, 2009, 24: 44-46.
L.J. Huang, L. Geng*, A.B. Li, G. S. Wang, X.P. Cui, Effects of Hot Compression and Heat Treatment on the Microstructure and Tensile Property of Ti-6.5Al-3.5Mo-1.5Zr-0.3Si Alloy, Materials Science and Engineering A, 2008, 489(1-2): 330-336.
L.J. Huang*, L. Geng, A.B. Li, G.S. Wang and L. Shi. Constitutive Equation and Hot Deformation Characteristic of Ti-6.5Al-3.5Mo-1.5Zr-0.3Si alloy with Equiaxed Microstructure. RARE METALS. 2007, 26: 88-93.
李爱滨, 耿林*, 黄陆军, 崔喜平, 徐斌, 李玉涛, TC11 钛合金热变形行为的研究, 稀有金属材料与工程, 2008, 37(3): 728-731.
石磊，耿林*，杨昭，李诚国，黄陆军, (α%2Bβ)相变区内变形量对TC11合金组织的影响, 稀有金属材料与工程, 2008, 37(3): 622-626.
京公网安备 11010802027423号