万敏 - 西北工业大学

个人简介

2005年4月留校工作，2007年4月任讲师，2009年破格晋升副教授，2012年遴选为博士生导师，2014年晋升为教授

研究领域

1、高效高精密加工理论 2、切削过程运动、几何及机理分析与建模 3、切削系统稳定性评估与主动控制 4、高性能切削刀具设计理论 5、机床运动建模与轮廓误差控制

近期论文

查看导师新发文章（温馨提示：请注意重名现象，建议点开原文通过作者单位确认）

M. Wan; Y. Altintas; Mechanics and Dynamics of Thread Milling Process, Int. J. of Mach. Tools Manuf. 87 (2014) 16-26. M. Wan, M.S. Lu, W.H. Zhang, Y. Yang, A New Ternary-Mechanism Model For The Prediction of Cutting Forces in Flat End Milling, Int. J. Mach. Tools Manuf. 57 (2012) 34-45. M. Wan, Y.T. Wang, W.H. Zhang, Y. Yang, J.W. Dang, Prediction of Chatter Stability For Multiple-Delay Milling System Under Different Cutting Force Models, Int. J. Mach. Tools Manuf. 51 (2011) 281-295. M. Wan, W.H. Zhang, J.W. Dang, Y Yang, A Unified Stability Prediction Method For Milling Process With Multiple Delays, Int. J. Mach. Tools Manuf. 50 (2010) 29-41. M. Wan, W.H. Zhang, J.W. Dang, Y Yang, New Procedures For Calibration of Instantaneous Cutting Force Coefficients and Cutter Runout Parameters in Peripheral Milling, Int. J. Mach. Tools Manuf. 49 (2009) 1144-1151. M. Wan, W.H. Zhang, Systematic Study On Cutting Force Modelling Methods For Peripheral Milling, Int. J. Mach. Tools Manuf. 49 (2009) 424-432. M. Wan, W.H. Zhang, G.H. Qin, Z.P. Wang, Strategies For Error Prediction and Error Control in Peripheral Milling of Thin-Walled Workpiece, Int. J. Mach. Tools Manuf. 48 (2008) 1366-1374. M. Wan, W.H. Zhang, G. Tan, G.H. Qin, An In-Depth Analysis of The Synchronization Between The Measured and Predicted Cutting Forces For Developing Instantaneous Milling Force Model, Int. J. Mach. Tools Manuf. 47 (2007) 2018-2030. M. Wan, W.H. Zhang, G.H. Qin, G. Tan, Efficient Calibration of Instantaneous Cutting Force Coefficients and Runout Parameters For General End Mills, Int. J. Mach. Tools Manuf. 47 (2007) 1767-1776. M. Wan, W.J. Pan, W.H. Zhang, Y.C. Ma, Y. Yang; A Unified Instantaneous Cutting Force Model For Flat End Mills With Variable Geometries, J. of Mater. Process. Technol; 214 (2014) 641-650. M. Wan, W.H. Zhang, Y. Yang, Phase Width Analysis of Cutting Forces Considering Bottom Edge Cutting and Cutter Runout Calibration in Flat End Milling of Titanium Alloy, J. Mater. Process. Technol. 211 (2011) 1852-1863. M. Wan, W.H. Zhang, G. Tan, G.H. Qin, Systematic Simulation Procedure of Peripheral Milling Process of Thin-Walled Workpiece, J. Mater. Process. Technol. 197 (2008) 122-131. M. Wan, W.H. Zhang, Efficient Algorithms For Calculations of Static Form Errors in Peripheral Milling, J. Mater. Process. Technol. 171 (2006) 156-165. M. Wan, W.H. Zhang, J.W. Dang, Y Yang, A Novel Cutting Force Modelling Method For Cylindrical End Mill, Appl. Math. Modelling 34 (2010) 823-836. M. Wan, W.H. Zhang, Calculations of Chip Thickness and Cutting Forces in Flexible End Milling, Int. J. Adv. Manuf. Technol. 29 (2006) 637-647. M. Wan, Y.C. Ma, W.H. Zhang, Y. Yang, Study On The Construction Mechanism of Stability Lobes in Milling Process With Multiple Modes. Adv. Manuf. Technol.79 (201 5)589-603. M. Wan; Z. Kilic, M; Y. Altintas, Mechanics and Dynamics of Multifunctional Tools; Asme J. Manuf. Sci. Eng.137 (2015) 011019. M. Wan, W.H. Zhang, K.P. Qiu, T. Gao, Y. H. Yang, Numerical Prediction of Static Form Errors in Peripheral Milling of Thin-Walled Workpieces With Irregular Meshes, Asme J. Manuf. Sci. Eng. 127 (2005) 13-22. M. Wan, W.H. Zhang, G.H. Qin, Z.P. Wang, Consistency Study On Three Cutting Force Modeling Methods For Peripheral Milling, Imeche J. Eng. Manuf. 222 (2008) 665-676. M. Wan, W.H. Zhang, G. Tan, G.H. Qin, New Algorithm For Calibration of Instantaneous Cutting-Force Coefficients and Radial Run-Out Parameters in Flat End Milling, Imeche J. Eng. Manuf. 221 (2007) 1007-1019. M. Wan, W.H. Zhang, G. Tan, G.H. Qin, New Cutting Force Modeling Approach For Flat End Mill, Chin. J. Aero. 20 (2007) 282-288.