由Podosphaera xanthii引起的葫芦白粉病是全球葫芦生产的经济制约因素。本研究考察了温度和蒸汽压不足 (VPD) 对澳大利亚P. xanthii分生孢子发芽率和胚芽管形成的影响接种后 12-48 小时隔离。通过接种黄瓜,cv.准备了两个实验。水晶色拉,使用孢子沉淀塔的叶盘。第一个实验在饱和蒸汽压 (SVP) 下在 8 到 35 °C 的八个温度下孵育接种的黄瓜叶盘,第二个实验在六个湿度室(33% - 99% 相对湿度)中比较了 0.038 和 1.797 kPa 之间的 18 个 VPD 条件) 和三个温度(22 °C、25 °C、28 °C)。清除叶盘、染色并在显微镜下检查分生孢子萌发和胚芽管的数量。SVP 的最佳发芽温度为 28ºC,其中超过 50% 的分生孢子在 12 小时内发芽,85% 的分生孢子在 48 小时内发芽。在 17 °C 和 31 °C 之间的其他温度处理 12 小时后,记录的发芽分生孢子较少。当蒸气压在 0.13 和 2.5 kPa 之间时,发芽率和发芽率显着降低,发芽响应 VPD 的变化约为 10%,表明分生孢子发芽与高于 0.13 kPa 的 VPD 相关联很困难。在接近 SVP 的最低 VPD 处理下,胚芽管产量在 25 ºC 和 28 ºC 之间最高,超过 50% 的发芽分生孢子产生至少三个胚芽管。当 VPD 增加时,发芽和胚芽管的形成显着减少。超过 50% 的萌发分生孢子产生至少三个胚芽管。当 VPD 增加时,发芽和胚芽管的形成显着减少。超过 50% 的萌发分生孢子产生至少三个胚芽管。当 VPD 增加时,发芽和胚芽管的形成显着减少。P. xanthii分生孢子能够在相对干燥的条件下(例如 2.53 kPa)产生初级胚芽管,但这些结果表明感染的可能性较小并且需要更长的孵育时间。这项研究提供了模拟葫芦科植物白粉病感染的第一个关键步骤,并可能导致能够提供风险预测或杀菌剂管理决策支持工具的模型。
"点击查看英文标题和摘要"
The influence of temperature and vapour pressure deficit on conidia germination and germ tube production in an Australian Podosphaera xanthii isolate
Powdery mildew of cucurbits, caused by Podosphaera xanthii, is an economic constraint in cucurbit production worldwide. This study examined the influence of temperature and vapour pressure deficit (VPD) on the rate of conidial germination and the formation of germ tubes in an Australian P. xanthii isolate 12 – 48 h after inoculation. Two experiments were prepared by inoculating cucumber, cv. crystal salad, leaf-discs using a spore settling tower. The first experiment incubated inoculated cucumber leaf-discs at eight temperatures between 8 and 35 °C under saturated vapour pressure (SVP), the second compared 18 VPD conditions between 0.038 and 1.797 kPa, in six humidity chambers (33% – 99% relative humidity) and three temperatures (22 °C, 25 °C, 28 °C). Leaf-discs were cleared, stained and microscopically inspected for conidial germination and the number of germ tubes. The optimal temperature for germination was 28ºC at SVP, where more than 50% of conidia had germinated by 12 h, and 85% by 48 h. Fewer germinated conidia were recorded after 12 h at other temperature treatments between 17 °C and 31 °C. The germination percentage and germination rate were significantly lower when vapour pressure was between 0.13 and 2.5 kPa, with germination in response to VPD varying by approximately 10%, indicating difficulty associating conidial germination to VPD above 0.13 kPa. Germ tube production was highest between 25 ºC and 28 ºC at the lowest VPD treatment at near SVP, with more than 50% of the germinated conidia producing at least three germ tubes. Germination and formation of germ tubes significantly reduced when VPD increased. P. xanthii conidia were able to produce a primary germ tube under relatively dry conditions, such as 2.53 kPa, but these results show infection would be less likely and require longer incubation. This study provides the first crucial step in simulating powdery mildew infections on cucurbit plants and may lead to a model capable of providing risk forecasts or fungicide management decision support tools.