杨续跃 - 中南大学 - 材料科学与工程学院

个人简介

1982年2月于中南工业大学材料系本科毕业。1991年作为日本文部省国费留学生赴国立电气通信大学留学，1996年获得博士学位后留校任助手和助教授。2008年回国工作并任中南大学教授。多次主持承担自然科学基金等国家项目，在国际知名期刊上发表论文150余篇，申请国家发明专利30余项，在国际会议上做特邀报告10余次。获得日本轻金属学会杰出论文奖、轻金属奖学会奖和日刊工业新闻社奖等多项国内外奖励。

研究领域

1.有色金属塑性变形、再结晶过程中组织的演变及控制 2.轻合金材料中高温蠕变、疲劳行为的研究 3.复杂显微结构镁合金的设计、制备与服役性能的研究

近期论文

查看导师最新文章（温馨提示：请注意重名现象，建议点开原文通过作者单位确认）

1. Enhancing creep properties of a hot-rolled Mg-4Y binary alloy via a new thought of inhibiting cross-slip, Materials Characterization, 147 (2019) 64-71. (SCI) 2. Creep behaviors of a highly concentrated Mg-18wt.%Gd binary alloy with and without artificial aging, Journal of Alloys and Compounds, 774 (2019) 1036-1045. (SCI) 3. Enhanced mechanical properties of a hot-extruded AZ80 Mg alloy rod by pre-treatments and post-hot compression, Journal of Alloys and Compounds, 740 (2018) 180-193. (SCI) 4. Dynamic recrystallization behaviors of Mg-Gd-Y-Zn-Zr alloy with different morphologies and distributions of LPSO phases, Materials Science and Engineering A, 715 (2018) 389-403. (SCI) 5. Damage analysis of hot-rolled AZ31 Mg alloy sheet during uniaxial tensile testing under different loading directions, Materials Science and Engineering A, 710 (2018) 289-299. (SCI) 6. Creep behaviors of hot compressed Mg-4Y-2Nd-0.2Zn-0.5Zr alloy with and without aging, Materials Science and Engineering A, 708 (2017) 460-468. (SCI) 7. Annealing behavior of a cast Mg-Gd-Y-Zr alloy with necklace fine grains developed under hot deformation. Materials Science & Engineering A 688 (2017) 280-288. (SCI) 8. Enhanced fatigue properties of cast AZ80 Mg alloy processed by cyclic torsion and low-temperature annealing. Materials Science & Engineering A 696 (2017) 52-59. (SCI) 9. Influence of Fe addition on annealing behaviors of a phosphorus containing brass. J. Alloy. Compd., 712 (2017) 268~276. (SCI) 10. Effect of heat treatment on dynamic recrystallization behaviors and mechanical properties of Mg–2.7Nd–0.5Zn–0.8Zr alloy. Materials Science & Engineering A 675 (2016) 128–137. (SCI) 11. Microstructural development under interrupted hot deformation and the mechanical properties of a cast Mg-Gd-Y-Zr alloy, Mater. Sci. Eng. A A, 652 (2016) 377~383. (SCI) 12. Dynamic recrystallization behaviors of a Mg-4Y-2Nd-0.2Zn-0.5Zr alloy and the resultant mechanical properties after hot compression. Materials and Design 97 (2016) 25-32. (SCI) 13. Effect of stacking fault energy on mechanical properties and annealing behavior of brasses. Journal of Alloys and Compounds 679 (2016) 400-407. (SCI) 14. Effect of initial orientation on the microstructure and mechanical properties of textured AZ31 Mg alloy during torsion and annealing, Mater. Design, 86 (2015) 526~535. (SCI) 15. Effects of rolling temperature and subsequent annealing on mechanical properties of ultrafine-grained Cu–Zn–Si alloy. Materials Characterization, 106 (2015) 100–107. (SCI) 16. Dynamic recrystallization behaviors and the resultant mechanical properties of a Mg–Y–Nd–Zr alloy during hot compression after aging. Materials Science & Engineering A 640 (2015) 51–60. (SCI) 17. Enhanced ductility and reduced asymmetry of Mg-2Al-1Zn alloy plate processed by torsion and annealing. Transactions of Nonferrous Metals Society of China 25 (2015) 3928-3935. (SCI) 18. Enhancement of strength and ductility of Cu–Sn–Zn alloy by iron addition. Materials Science& Engineering A 612 (2014) 246–252. (SCI) 19. Enhanced strength and electrical conductivity of Cu-Zr-B alloy by double deformation-aging process. Journal of Alloys and Compounds, , 615 (2014): 249-254. (SCI) 20. Structural development at severely high strain in AZ31 magnesium alloy processed by cold forging and subsequent annealing, Mater Des. 44 (2013) 573–579. (SCI)